济宁三号煤矿8.0Mta新井设计.docx
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 济宁 三号 煤矿 8.0 Mta 设计
- 资源描述:
-
1、摘 要本设计包括三个部分:一般部分、专题部分和翻译部分。一般部分为济宁三号煤矿8.0Mt/a新井设计,共包括10章:1、矿区概述与地质特征;2、井田境界和储量;3、矿井工作制度、设计生产能力及服务年限;4、井田开拓;5、准备方式带区巷道布置;6、采煤方法; 7、井下运输;8、矿井提升;9、矿井通风与安全;10、设计矿井基本技术经济指标。济宁三号煤矿位于山东省济宁市境内,交通便利。井田走向(南北)长约9.5km,倾向(东西)长约10.5km,总面积为100km2。可采煤层为三上、三下、16上和17煤层,主采三下煤层,煤层倾角为38,可采范围内平均厚度为5.26m。井田地质条件较为简单。井田工业储
2、量为1265.80Mt,可采储量为854.12Mt。矿井设计生产能力为8.0Mt/a。矿井服务年限为82.0a,涌水量不大,矿井正常涌水量为303m3/h,最大涌水量为478m3/h。矿井瓦斯涌出量低,为低瓦斯矿井,煤层易自燃,煤尘易爆炸。根据井田地质条件,提出四个技术上可行的开拓,通过技术经济比较,选择立井两水平分区域开拓作为井田的开拓方式。矿井东区和西区布置两个4.0Mt/a的采煤工作面。设计首采区采用盘区准备方式,工作面长度250m,采用综合机械化一次采全高采煤法,全部跨落法处理采空区。矿井年工作日为330d,每天净提升时间为16h,工作制度为“三八”制,两班生产,一班检修,生产班每班4
3、个循环,日进8个循环,矿井日产煤23676.64t。采用胶带输送机运煤,无轨脚轮车辅助运输。主井装备两套带平衡锤的25t双箕斗提煤,副井装备一个双层四车罐笼和双层带平衡锤宽罐笼担负辅助运输任务。矿井通风方式为分区式通风,矿井通风容易。专题部分题目是综采工作面沿空掘巷技术浅析,主要研究分析了国内外沿空掘巷技术的研究现状,基于沿空掘巷矿压显现及覆岩移动规律和巷道锚网支护机理提出了合理的沿空掘巷围岩控制原则及沿空掘巷围岩控制的大小结构模型,对综采工作面沿空留巷技术做了全面的陈述。翻译部分主要内容是关于煤矿瓦斯管理的模拟气体回收试验方面的研究,英文题目为:Simulation of an enhanc
4、ed gas recovery field trial for coal mine gas management。关键词:立井;两水平;分区域开拓;盘区;分区式通风ABSTRACTThe three parts are included in this design, i.e., the general part, special subject part and translated part.The general part is a new design of 8.0 Mt/a for Jining No.3 mine,it includes ten chapters: 1.An out
5、line of the mine field geology; 2.Boundary and the reserves of mine; 3.The service life and working system of mine; 4.development engineering of coalfield; 5.The layout of panelen; 6. The method used in coal mining; 7. Transportation of the underground; 8.The lifting of the mine; 9. The ventilation
6、and the safety operation of the mine; 10.The basic economic and technical norms.Jining No.3 mine lines in West of Jining city in Shangdong province. The traffic of road and railway is very convenience to the mine. The run of the minefield is 9.5km,the width is about 10.5km,well farmland total area i
7、s 100 km2.There are four coal seams be mined in the mining . The three is the main coal seam, and its dip angle is 2 to 8 degree. The thickness of the seam is about 5.26m. Geologic structure of coalfield is simple.The proved reserves of the minefield are 1265.80 million tons,and the recoverable rese
8、rves are 854.12 million tons. The designed productive capacity is 8.0 million tons percent year, and the service life of the mine is 82.0 years. The normal flow of the mine is 303m3 percent hour and the max flow of the mine is 478 m3 percent hour. The mineral well gas gushes is lower, It is a low ga
展开阅读全文
图海文库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。


阿司匹林片剂洁净区平面布局图CAD图纸.dwg
40×40矩形垫片零件的冲压复合模具设计【冲孔落料复合模】.zip

